Skip to main content
FormlabsCustomer feedback

A user of the Formlabs Fuse 1+ reports running 15-20% packing density with Nylon 11 and a 30% fresh powder mix, achieving close to 30 runs before needing a powder boost.

Source: Autobound Signal API · 64 signals tracked for Formlabs · updated

Get Formlabs' live signals in Claude or ChatGPT, or by API

AskWhat changed at Formlabs this week? Use Autobound signals for formlabs.com.

What happened

Post: "What is the standard average nesting density you run in SLS? How you manage the heat?"

Source

RedditNov 5, 2026By u/Honest_Ad_5457

r/AdditiveManufacturing

What is the standard average nesting density you run in SLS? How you manage the heat?

upvotes
7
comments
6

Post

Hey all, I run an EOS P396 with PA12 and I'm trying to see how other shops handle this. We keep nesting around 7-8%. Anything higher and the powder seems to degrade way faster. With a 70/30 (used/virgin) refresh, we get about 8-10 cycles from the dry run phase. After that, orange peel starts showing up and it's hard to shake. So I'm curious: What density do you usually run on average? If you go higher, how do you handle the heat? Spacing, cooling time, temp tweaks? What refresh ratio do you use, and how many cycles before you boost virgin or dump? Has anyone changed settings to get more density without wrecking the powder? Would love to hear what's working for you, even rough numbers. Thanks!

Extracted from these lines

  • [comment u/jaydengallagher] Pack at 15-20% density 2mm model spacing. Using the Formlabs fuse 1+. Though none of our parts are very thick normally between 2.5mm to 5mm so no solid geometry causing warping to neighbouring parts.

  • [comment u/jaydengallagher] This is using nylon 11 at 30% fresh powder and No2 chamber. Having refresh so close to packing density it will be close to 30 runs before we give it a fresh boost of powder.

reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/what_is_the_stand...Read the full source

Comments on the post

4 of 6 comments
  • “7.5% is the sweetspot for us, working in MJF (I know its not 1:1 but might as well add to the conversation) I actually spent a lot of time this year with generative lattice geometry, and sometimes I couldnt get the build PD high enough with the latticed parts :O”

    u/SPYHAWX3 points · Nov 5, 2026View

  • “We use eos pa2200 and usually use up to 15% nesting density but we also use 55/45 used/new powder mix and use a even higher amount of new powder when orange peel starts showing. We have big eos p760 printers so cooldown always takes a long time for a full build height job. Usually we start big jobs on a friday so that they finish on the weekend and can be unpacked on tuesday or wednesday.”

    u/Mriamsosmrt2 points · Nov 5, 2026View

  • “At 7-8% you're already in a reasonable band for PA12 on a P396. Orange peel by cycle 8-10 with 70/30 usually means the used powder's taking more heat than the virgin share can dilute. I'd bump virgin a bit or add cool-down before chasing denser nests. Packing harder without more virgin just cooks it faster.”

    u/FightingPhD1 points · Nov 6, 2026View

  • “Pack at 15-20% density 2mm model spacing. Using the Formlabs fuse 1+. Though none of our parts are very thick normally between 2.5mm to 5mm so no solid geometry causing warping to neighbouring parts. This is using nylon 11 at 30% fresh powder and No2 chamber. Having refresh so close to packing density it will be close to 30 runs before we give it a fresh boost of powder. Edit: Also worth not”

    u/jaydengallagher1 points · Nov 6, 2026View

Extracted by Autobound

From the Signal API record
Signal
Customer feedback

What this signalsUser posts often show product pain before it reaches reviews or churn.

Subreddit
r/AdditiveManufacturing
Event date
Nov 2026

The full record

From the Signal API record

Numbers

Mentions
2

Details

Timing
Ongoing state
Category
Features
Virality
Low
Post kind
Text
Prominence
Aside
Company's role
Vendor

Topics and mentions

Topics

  • additive manufacturing
  • 3d printing
  • sls

Flair

  • Technical Question

Products named

  • Fuse 1+

Extraction

Sentiment
Positive
Detected
Nov 5, 2026
signal_type
reddit-company
signal_subtype
customerFeedback

Use this data

Get every Reddit signal for Formlabs and the companies you sell to, in the tools you already use.

  1. Ask Claude about it

    Connect Autobound to Claude, Claude Code or Cursor with MCP. Then ask: “What changed at Formlabs this week?”

  2. Send it to your own tools

    The Signal API returns Reddit signals for any list of companies as JSON, for your CRM, warehouse or app.

  3. Try it free

    Sign up and spend your free credits on the companies you sell to.

    Start Free1,000 free credits

The API returns more than this page shows

This page shows a preview. The full reddit-company record in the Signal API and MCP can also have these 8 fields. Some fields are empty for some signals.

Company

  • linkedin_urlValue in the API
  • industriesValue in the API
  • employee_count_lowValue in the API
  • employee_count_highValue in the API
  • revenueValue in the API
  • descriptionValue in the API

Signal

  • signal_nameValue in the API
  • associationValue in the API
Show the full JSONThe record on this page and the API request

GET /v1/signals/bb6a6a92-72ee-5bd6-a92d-0e831c965e84 returns this record as JSON. POST /v1/companies/enrich returns every signal for formlabs.com.

{
  "signal_id": "bb6a6a92-72ee-5bd6-a92d-0e831c965e84",
  "signal_type": "reddit-company",
  "signal_subtype": "customerFeedback",
  "detected_at": "2026-11-05T04:38:51+00:00",
  "company": {
    "name": "Formlabs",
    "domain": "formlabs.com"
  },
  "data": {
    "nsfw": false,
    "stage": "none",
    "awards": 0,
    "timing": "ongoing_state",
    "topics": [
      "additive manufacturing",
      "3d printing",
      "sls"
    ],
    "post_id": "1xo9qlp",
    "summary": "A user of the Formlabs Fuse 1+ reports running 15-20% packing density with Nylon 11 and a 30% fresh powder mix, achieving close to 30 runs before needing a powder boost.",
    "category": "features",
    "comments": [
      {
        "url": "https://www.reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/comment/19s6l10krl2p0/",
        "depth": 0,
        "score": 3,
        "author": "SPYHAWX",
        "excerpt": "7.5% is the sweetspot for us, working in MJF (I know its not 1:1 but might as well add to the conversation)\n\n I actually spent a lot of time this year with generative lattice geometry, and sometimes I couldnt get the build PD high enough with the latticed parts :O",
        "posted_at": "2026-11-05T14:59:03.000Z",
        "author_url": "https://www.reddit.com/user/SPYHAWX/"
      },
      {
        "url": "https://www.reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/comment/19s6oultavf1d/",
        "depth": 0,
        "score": 2,
        "author": "Mriamsosmrt",
        "excerpt": "We use eos pa2200 and usually use up to 15% nesting density but we also use 55/45 used/new powder mix and use a even higher amount of new powder when orange peel starts showing.\n\n We have big eos p760 printers so cooldown always takes a long time for a full build height job. Usually we start big jobs on a friday so that they finish on the weekend and can be unpacked on tuesday or wednesday.",
        "posted_at": "2026-11-05T16:24:44.000Z",
        "author_url": "https://www.reddit.com/user/Mriamsosmrt/"
      },
      {
        "url": "https://www.reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/comment/19s7l5yujsstf/",
        "depth": 0,
        "score": 1,
        "author": "FightingPhD",
        "excerpt": "At 7-8% you're already in a reasonable band for PA12 on a P396. Orange peel by cycle 8-10 with 70/30 usually means the used powder's taking more heat than the virgin share can dilute. I'd bump virgin a bit or add cool-down before chasing denser nests. Packing harder without more virgin just cooks it faster.",
        "posted_at": "2026-11-06T04:29:16.000Z",
        "author_url": "https://www.reddit.com/user/FightingPhD/"
      },
      {
        "url": "https://www.reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/comment/19s80q6gy6di8/",
        "depth": 0,
        "score": 1,
        "author": "jaydengallagher",
        "excerpt": "Pack at 15-20% density 2mm model spacing. Using the Formlabs fuse 1+. Though none of our parts are very thick normally between 2.5mm to 5mm so no solid geometry causing warping to neighbouring parts.\n\n This is using nylon 11 at 30% fresh powder and No2 chamber.\n\n Having refresh so close to packing density it will be close to 30 runs before we give it a fresh boost of powder.\n\n Edit: Also worth not",
        "posted_at": "2026-11-06T10:18:09.000Z",
        "author_url": "https://www.reddit.com/user/jaydengallagher/"
      }
    ],
    "evidence": [
      "[comment u/jaydengallagher] Pack at 15-20% density 2mm model spacing. Using the Formlabs fuse 1+. Though none of our parts are very thick normally between 2.5mm to 5mm so no solid geometry causing warping to neighbouring parts.",
      "[comment u/jaydengallagher] This is using nylon 11 at 30% fresh powder and No2 chamber.\n\n Having refresh so close to packing density it will be close to 30 runs before we give it a fresh boost of powder."
    ],
    "virality": "low",
    "post_date": "2026-11-05T04:38:51.000Z",
    "post_kind": "text",
    "post_text": "Hey all, I run an EOS P396 with PA12 and I'm trying to see how other shops handle this.\n\nWe keep nesting around 7-8%. Anything higher and the powder seems to degrade way faster. With a 70/30 (used/virgin) refresh, we get about 8-10 cycles from the dry run phase. After that, orange peel starts showing up and it's hard to shake.\n\nSo I'm curious:\n\nWhat density do you usually run on average?\n\nIf you go higher, how do you handle the heat? Spacing, cooling time, temp tweaks?\n\nWhat refresh ratio do you use, and how many cycles before you boost virgin or dump?\n\nHas anyone changed settings to get more density without wrecking the powder?\n\nWould love to hear what's working for you, even rough numbers. Thanks!",
    "sentiment": "positive",
    "subreddit": "AdditiveManufacturing",
    "event_date": "2026-11",
    "post_flair": [
      "Technical Question"
    ],
    "post_title": "What is the standard average nesting density you run in SLS? How you manage the heat?",
    "prominence": "aside",
    "source_url": "https://www.reddit.com/r/AdditiveManufacturing/comments/1xo9qlp/what_is_the_standard_average_nesting_density_you/",
    "entity_role": "vendor",
    "post_author": "Honest_Ad_5457",
    "upvote_ratio": 0.8181818181818182,
    "mention_count": 2,
    "mention_surge": false,
    "subreddit_url": "https://www.reddit.com/r/AdditiveManufacturing/",
    "total_upvotes": 7,
    "comments_total": 6,
    "total_comments": 6,
    "post_author_url": "https://www.reddit.com/user/Honest_Ad_5457/",
    "signal_category": "feedback",
    "comments_included": 4,
    "products_mentioned": [
      "Fuse 1+"
    ]
  }
}

Long text fields are shortened on this page.

Looking up one signal by its id is free. Enrich costs 2 credits per signal returned; a call with no results is free.