Skip to main content
HPCustomer feedback

A network administrator reports several ageing HP switches failing in their environment, prompting replacements with Juniper switches.

Source: Autobound Signal API · 121 signals tracked for HP · updated

Get HP's live signals in Claude or ChatGPT, or by API

AskWhat changed at HP this week? Use Autobound signals for hp.com.

What happened

Post: "Readying a switch"

Source

RedditNov 3, 2026By u/Electronic-Block-746

r/Juniper

Readying a switch

upvotes
7
comments
10

Post

Highlighted: the lines this signal was extracted from

Hello I've recently taken over a role where there are a number of ageing HP switches that need to be replaced with Juniper switches. Prior to my arrival, several of the HP switches had already started to fail, so I'm keen to be prepared in case another one goes offline unexpectedly.I have new Juniper switches available and ready to deploy. What configuration and preparation work would you recommend carrying out in advance to ensure a replacement can be installed and brought into service as quickly as possible if an HP switch fails? Any best practices or recommendations would be greatly appreciated.

reddit.com/r/Juniper/comments/1xn43um/readying_a_switchRead the full source

Comments on the post

5 of 10 comments
  • “First thing is I burn the switch in at least over a weekend to make sure you don't have a dud power supply or bad fan. And upgrade the code on it to the recommended version. Then you're in a good position.”

    u/ZeniChan3 points · Nov 3, 2026View

  • “Back up your current configs and have copies of those available offline. Get familiar with how the existing architecture works, and get that documented. Look into network monitoring solutions like LibreNMS.”

    u/Doc_Blox3 points · Nov 3, 2026View

  • “It’s ultimately dependant on what you need your switch to do (SW, VLANs, 802.1X - These could vary a whole lot), you could look at the configurations on your HP switches and match the configuration on the EXs to make this easier with what you are currently running. Here’s a small list of best practices, but again, this is ultimately what you need to run in your network: https://networkingdocs.”

    u/ETH4N3T2 points · Nov 3, 2026View

  • “You need to build a config that meets/matches the outline of the current configuration in your environment, so you need to review that configuration and find out where there are constants, make sure those get into your template, and then from there you apply it to a replacement unit, and build it for the specific deployment site with more specific parameters.”

    u/PP_Mclappins1 points · Nov 4, 2026View

  • “Check out SolarWinds (Kiwi) CatTools. It automatically backs up network configs & generates a report when there is a change.”

    u/Basic_Platform_50011 points · Nov 6, 2026View

Extracted by Autobound

From the Signal API record
Signal
Customer feedback

What this signalsUser posts often show product pain before it reaches reviews or churn.

Subreddit
r/Juniper
Stage
Switching
Event date
Nov 2026

Companies

  • Juniper NetworksAlso named

The full record

From the Signal API record

Numbers

Mentions
3

Details

Timing
Ongoing state
Category
Reliability
Virality
Medium
Post kind
Text
Prominence
Core
Company's role
Vendor

Topics and mentions

Topics

  • hardware failure
  • switches
  • networking

Products named

  • HP switches

Extraction

Sentiment
Negative
Detected
Nov 3, 2026
signal_type
reddit-company
signal_subtype
customerFeedback

Use this data

Get every Reddit signal for HP and the companies you sell to, in the tools you already use.

  1. Ask Claude about it

    Connect Autobound to Claude, Claude Code or Cursor with MCP. Then ask: “What changed at HP this week?”

  2. Send it to your own tools

    The Signal API returns Reddit signals for any list of companies as JSON, for your CRM, warehouse or app.

  3. Try it free

    Sign up and spend your free credits on the companies you sell to.

    Start Free1,000 free credits

The API returns more than this page shows

This page shows a preview. The full reddit-company record in the Signal API and MCP can also have these 8 fields. Some fields are empty for some signals.

Company

  • linkedin_urlValue in the API
  • industriesValue in the API
  • employee_count_lowValue in the API
  • employee_count_highValue in the API
  • revenueValue in the API
  • descriptionValue in the API

Signal

  • signal_nameValue in the API
  • associationValue in the API
Show the full JSONThe record on this page and the API request

GET /v1/signals/14d32d40-949f-5a9a-a5c7-136acaaaecec returns this record as JSON. POST /v1/companies/enrich returns every signal for hp.com.

{
  "signal_id": "14d32d40-949f-5a9a-a5c7-136acaaaecec",
  "signal_type": "reddit-company",
  "signal_subtype": "customerFeedback",
  "detected_at": "2026-11-03T20:24:58+00:00",
  "company": {
    "name": "HP",
    "domain": "hp.com"
  },
  "data": {
    "nsfw": false,
    "stage": "switching",
    "awards": 0,
    "timing": "ongoing_state",
    "topics": [
      "hardware failure",
      "switches",
      "networking"
    ],
    "post_id": "1xn43um",
    "summary": "A network administrator reports several ageing HP switches failing in their environment, prompting replacements with Juniper switches.",
    "category": "reliability",
    "comments": [
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s3fm8mbpxd1/",
        "depth": 0,
        "score": 3,
        "author": "ZeniChan",
        "excerpt": "First thing is I burn the switch in at least over a weekend to make sure you don't have a dud power supply or bad fan. And upgrade the code on it to the recommended version. Then you're in a good position.",
        "posted_at": "2026-11-03T20:36:22.000Z",
        "author_url": "https://www.reddit.com/user/ZeniChan/"
      },
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s3gh9cy9929/",
        "depth": 0,
        "score": 3,
        "author": "Doc_Blox",
        "excerpt": "Back up your current configs and have copies of those available offline. Get familiar with how the existing architecture works, and get that documented. Look into network monitoring solutions like LibreNMS.",
        "posted_at": "2026-11-03T20:55:41.000Z",
        "author_url": "https://www.reddit.com/user/Doc_Blox/"
      },
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s3fsm6oa1wh/",
        "depth": 0,
        "score": 2,
        "author": "ETH4N3T",
        "excerpt": "It’s ultimately dependant on what you need your switch to do (SW, VLANs, 802.1X - These could vary a whole lot), you could look at the configurations on your HP switches and match the configuration on the EXs to make this easier with what you are currently running.\n\n Here’s a small list of best practices, but again, this is ultimately what you need to run in your network:\n\n https://networkingdocs.",
        "posted_at": "2026-11-03T20:40:21.000Z",
        "author_url": "https://www.reddit.com/user/ETH4N3T/"
      },
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s3tearj8kde/",
        "depth": 0,
        "score": 1,
        "author": "PP_Mclappins",
        "excerpt": "You need to build a config that meets/matches the outline of the current configuration in your environment, so you need to review that configuration and find out where there are constants, make sure those get into your template, and then from there you apply it to a replacement unit, and build it for the specific deployment site with more specific parameters.",
        "posted_at": "2026-11-04T01:45:18.000Z",
        "author_url": "https://www.reddit.com/user/PP_Mclappins/"
      },
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s8l5kyl8eg2/",
        "depth": 0,
        "score": 1,
        "author": "Basic_Platform_5001",
        "excerpt": "Check out SolarWinds (Kiwi) CatTools. It automatically backs up network configs & generates a report when there is a change.",
        "posted_at": "2026-11-06T17:56:09.000Z",
        "author_url": "https://www.reddit.com/user/Basic_Platform_5001/"
      },
      {
        "url": "https://www.reddit.com/r/Juniper/comments/1xn43um/comment/19s3igbn6in8l/",
        "depth": 0,
        "score": 1,
        "author": "Rek3030",
        "excerpt": "First figure out the config of those HP switches you're replacing, and what needs to go on the new switch.\n\n Figure out the best way to update the new switches you got, maybe just be one hop to the latest mature upgrade, if its several, you can use the USB method (takes some time but I find it less annoying then upgrading a switch 3-4 times to the newest version.\n\n - https://supportportal.juniper.",
        "posted_at": "2026-11-03T21:39:57.000Z",
        "author_url": "https://www.reddit.com/user/Rek3030/"
      }
    ],
    "evidence": [
      "[post] I've recently taken over a role where there are a number of ageing HP switches that need to be replaced with Juniper switches.",
      "[post] Prior to my arrival, several of the HP switches had already started to fail, so I'm keen to be prepared in case another one goes offline unexpectedly."
    ],
    "virality": "medium",
    "post_date": "2026-11-03T20:24:58.000Z",
    "post_kind": "text",
    "post_text": "Hello\n\nI've recently taken over a role where there are a number of ageing HP switches that need to be replaced with Juniper switches.\n\nPrior to my arrival, several of the HP switches had already started to fail, so I'm keen to be prepared in case another one goes offline unexpectedly.I have new Juniper switches available and ready to deploy.\n\nWhat configuration and preparation work would you recommend carrying out in advance to ensure a replacement can be installed and brought into service as quickly as possible if an HP switch fails?\n\nAny best practices or recommendations would be greatly appreciated.",
    "sentiment": "negative",
    "subreddit": "Juniper",
    "event_date": "2026-11",
    "post_title": "Readying a switch",
    "prominence": "core",
    "source_url": "https://www.reddit.com/r/Juniper/comments/1xn43um/readying_a_switch/",
    "entity_role": "vendor",
    "post_author": "Electronic-Block-746",
    "upvote_ratio": 1,
    "mention_count": 3,
    "mention_surge": true,
    "subreddit_url": "https://www.reddit.com/r/Juniper/",
    "total_upvotes": 7,
    "comments_total": 10,
    "total_comments": 10,
    "event_date_text": "Prior to my arrival",
    "other_companies": [
      {
        "name": "Juniper Networks",
        "role": "switching_to",
        "domain": "juniper.net"
      }
    ],
    "post_author_url": "https://www.reddit.com/user/Electronic-Block-746/",
    "signal_category": "feedback",
    "comments_included": 6,
    "products_mentioned": [
      "HP switches"
    ]
  }
}

Long text fields are shortened on this page.

Looking up one signal by its id is free. Enrich costs 2 credits per signal returned; a call with no results is free.